Saturday, August 8, 2015
Nilfisk C120.3 C125.3 C130.1 User Guide & Spares
Nilfisk C 120.3
Nilfisk C 125.3
Nilfisk C 130.1 X-TRA
USER GUIDE & COMMON SPARES
Operating your Nilfisk pressure washer
Mounting of high pressure hose
Attach the high pressure hose to the spray gun. Detach the high pressure hose by pressing the pawl (A).
Connection of high pressure hose
Mount the high pressure hose on the outlet
Mounting of spray lance and Click & Clean nozzles
Push the spray lance into the spray gun and screw it on. Note: The Nilfisk spray lance has a built-in low pressure nozzle that can be used for flushing away dirt. Warning: When attaching the Click & Clean nozzles, the pawl on the side of the spray lance should come out again. Note: The Nilfisk Tornado PR nozzle and the foam sprayer feature a swivel lock, which must be positioned in the hole in the Click & Clean spray. Press the pawl to detach the Click & Clean nozzle.
Water connection
An ordinary 1/2" garden hose of min. 10 m and max. 25 m will be suitable. Only use water without any impurities. If there is a risk of running sands in the inlet water (i.e. from your own supply), an additional filter should be mounted.
Let the water run through the water hose before connecting it to the machine to prevent sand and dirt from penetrating the machine. Note: Check that the filter is fitted in the water inlet pipe and that it is not clogged up.
2. Connect the water hose to the water supply by means of the quick connector (inlet water, max. pressure: 10 bar, max. temperature: 40°C).
3. Turn on the water.
Start and stop of the machine (when connected to a water supply)
The spray lance is affected by a thrust during operation - therefore always hold it firmly with both hands. IMPORTANT: Point the nozzle at the ground.
Check that the machine is in upright position. NOTE: Do not place the machine in high grass!
2. Release the trigger lock.
3. Activate the trigger of the spray gun and let the water run until all air has escaped from the water hose.
4. Turn the start/stop switch to position "I".
5. Activate the trigger of the spray gun. Always adjust the distance and thus the pressure of the nozzle to the surface, which is to be cleaned. Do not cover the machine during operation. Note: If the machine is left or not used for 5 minutes, it must be switched off on the start/stop switch "O" (1):
1. Turn the start/stop switch to position "O".
2. Disconnect the electrical plug from the socket.
3. Shut off the water supply and activate the trigger to relieve the machine of pressure.
4. Lock the spray gun. When releasing the trigger of the spray gun, the machine automatically stops. The machine will start again when you re-activate the spray gun.
Start the machine when connected to open containers.
The washer can take in water from a rain water tank as an example. The hose for the water supply must not be too long, approx. 5 m. Make sure that the water tank is not placed on a lower level than the machine.
1. Place the other end of the water hose in the water tank. Use an external filter if the water contains impurities.
2. Turn the start/stop switch (1) to position "I".
3. Activate the trigger of the spray gun and let the water run, until the air has escaped from the water hose and the pump.
4. Mount spray lance and nozzle.
Pressure regulation on the Nilfisk TORNADO PR Nozzle
The pressure can be regulated on the Nilfisk TORNADO PR nozzle.
Fields of application and working Methods
General
Efficient high pressure cleaning is achieved by following a few guidelines, combined with your own personal experience of specific cleaning tasks. Accessories and detergents, when correctly chosen, can increase the efficiency of your pressure washer. Here is some basic information about cleaning.
Detergent and foam
Foam or detergent should be applied onto dry surfaces so that the chemical product is in direct contact with the dirt. Detergents are applied from bottom to top, for example on a car bodywork, in order to avoid "super clean" areas, where the detergent collects in higher concentration and streams downwards. Let the detergent work for several minutes before rinsing but never let it dry on the surface being cleaned. Note: It is important that the detergents do not dry up. Otherwise the surface that has to be cleaned can be damaged.
Mechanical effect
In order to break down tough layers of dirt, additional mechanical effect may be required. Special wash brushes offer this supplementary effect that cuts through dirt (especially by car washing).
Typical fields of application
Below you will find a description of a lot of cleaning tasks which can be solved by a pressure washer from Nilfisk in association with accessories and detergents.
Car. Accessories required: Car nozzle, auto brush, under chassis nozzle, Foam sprayer, Car Combi Cleaner
1. Apply Car Combi Cleaner with the foam sprayer. Always start from the bottom and work upwards. Let Car Combi Cleaner act for at least 5 min.
2. Wash the car with the car nozzle, which has been optimized for quick and gentle cleaning of enamelled surfaces (the jet is wider and not so sharp). Start at the front of the car and work backwards to avoid water from penetrating by the door mouldings.
3. Use the brush for removal of traffic film which is not removed by the nozzle. If the car is very dirty, apply Car Combi Clean er again.
4. Attach the undercarriage nozzle and clean undercarriage and wheel arches.
5. Remove water from the surface of the car with the scraper on the car brush. Make sure that all grains of sand etc. have been removed before using the scraper. Wipe with a wash leather where the scraper cannot reach.
Flagstones, concrete, floors and other hard surfaces. Accessories required: Powerspeed, Stone & Wood, Cleaner, Patio Cleaner
Wash towards outlets or the like. On surfaces with moss or algae you may start by applying Stone & Wood Cleaner with the foam sprayer. Wash before the soap dries. Another more effective and quicker method is to use the Patio Cleaner. Thus you will also avoid splashes.
Cleaning of drain pipes, outlets, down pipes etc. accessories required: Drain Cleaning Hose
Push the tube cleaner approx. ½ m (to mark) into a tube or drain and activate the trigger of the spray handle. The nozzle opening turning backwards will pull the cleaner through the tube. The nozzle will break down the „plug“ and flush the dirt backwards.
Nilfisk Pressure Washer Troubleshooting
click to enlarge
Consumable Spare Part Numbers for:
Nilfisk C 125.3-8 PCCAR (EU) CENTENNIAL
Nilfisk C 125.3-8 PCAD
Nilfisk C 120.3-6
Nilfisk C 120.3-6 PA
Nilfisk C 120.3-6 PAD
Nilfisk C 120.3-6 PC
Nilfisk C 125.3-8
Nilfisk C 125.3-8 PAD
Nilfisk C 125.3-8 PC
Nilfisk C 125.3-8 PCD
Nilfisk C 120.3-6 PC CAR
Nilfisk C 120.3-6 PD AUTO
Nilfisk C 125.3-8 CAR C 125.3-8 PA
Nilfisk C 120.3-6 P
Gun 126481132
Hose 128500080
Lance 126481134
Tornado Nozzle 126481116
Powerspeed Nozzle 126481115
Patio Cleaner 126411376
Others
This blog was brought to you by SparesGiant. Pressure Washer, Cleaning Equipment and Garden Machinery spare parts specialist
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment